- WCS1800 through hole current sensorHall effect current sensor for […]
- Lan Controller v2 housingUniversal housing fit to Lan Controller […]
- Extension cable Splitter RJ11Extension cable SPLITTER DS18B20 SENSOR […]
- DHT Sensor connection cable 60 cm60cm cables are suitable for […]
- DHT Sensor connection cable 35 cmThe cables with a length of 33cm […]
- DHT Sensor connection cable 30 cmThe cables with a length of 30cm […]
- AC Current Clamp Sensor SCT-01Non-invasive current transformer, […]
- Current Sensor Carrier -75A to +75A ACS709This board is a simple carrier of […]
- ACS711EX Current Sensor Carrier -31A to +31AThis board is a simple carrier of […]
- ACS711EX Current Sensor Carrier -15.5A to +15.5AThis board is a simple carrier of […]
- Air quality sensor SDS-011Air quality sensor SDS-011 use laser […]
- Sensor- door open / reed sensor with 15cm cableThe magnetic contacts are an important […]
- Modules sensor watherTECHNICAL SPECIFICATIONS Power supply […]
- Waterproof temperature sensor DS18B20 1mTECHNICAL SPECIFICATIONS Temperature […]
- Light detector moduleThe sensor is used to detect light. […]
- Rain detector moduleThe sensor is used to detect […]
- Sensor- door open / reed sensorMagnetic sensor are essential component […]
- Magnetic water level CMW55Float liquid level sensors are used […]
- Magnetic water level CMW65Float liquid level sensors are used […]
- Magnetic water level CMW45Float liquid level sensors are used […]
- Magnetic water level CMW35Float liquid level sensors are used […]
- Infrared distance sensor 20-150cm SharpSharp is analog distance sensor using […]
- Moisture/flooding sensorSensor is open electric curcuit with […]
- PIR motion sensorPIR sensor type HC-SR501 allows for […]
- Temperature sensor DS18B20 1Wire to Lan ControllerTemperature sensor with cable and RJ11 […]
- The temperature sensor PT1000 to Lan ControllerTemperature sensor based on PT1000 […]
- Humidity and temperature sensor DHT22 AM2302Humidity and temperature sensor DHT22 […]
- Humidity and temperature sensor AM2320Digital sensor with I2C bus output. […]
- Dusk sensorDusk sensor are circuit of specially […]
- Relays board 10A v3Accessory board with 4pcs of high […]
- Control board ON/OFF/PWMThe board is designed as an overlay on […]
- PoE injector 4xLAN/PoEPoE injector with reseting board. It […]
- Splitter DS18B20 sensof for Lan ControllerMultiplication 1Wire input (Screw […]
- Splitter RJ12 sensor DS18B20 for Lan ControllerMultiplication 1Wire and I2C input […]
- Tile relay to the Lan controller/ GSM v3 12VThe 1 relays board. After connecting to […]
- Relays board 16A x 5 to LAN/GSMAccesory board with 5pcs of high […]
- Expansion Board v3 LiteProvide simple exit of ports IDC10-1 […]
Current Sensor Carrier -75A to +75A ACS709
This board is a simple carrier of Allegro’s +- 75 A ACS709 Hall effect-based linear current sensor with overcurrent fault output, which offers a low-resistance (~1.1 mΩ) current path and electrical isolation up to 100 V.
This board is a simple carrier of Allegro’s ±75A ACS709 Hall effect-based linear current sensor with overcurrent fault output, which offers a low-resistance (~1.1 mΩ) current path and electrical isolation up to 2.1 kV RMS. The sensor has optimized accuracy for currents from -37.5 A to 37.5 A, and the analog voltage output is linear for current magnitudes up to 75 A. The ratiometric output voltage is centered at VCC/2 and has a typical error of ±2%. It operates from 3 V to 5.5 V, so it can interface directly to both 3.3 V and 5 V systems.
This current sensor is a carrier board or breakout board for Allegro’s ACS709LLFTR-35BB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS709 datasheet (483k pdf) before using this product. The sensor has an operating voltage of 3 V to 5.5 V and an output sensitivity of 18.5 mV/A when Vcc is 3.3 V (or 28 mV/A when Vcc is 5 V). The following list details some of the sensor’s key features:
Optimized accuracy for bidirectional input current from -37.5 A to 37.5 A, with a linear sensing range from -75 A to 75 A (see warning note below for thermal limitations).
Conductive path internal resistance is typically 1.1 mΩ, and the PCB is made with 2-oz copper, so very little power is lost in the board. Integrated shield greatly reduces capacitive coupling from current conductor to die and prevents offset drift in high-side applications.
Use of a Hall effect sensor means the IC is able to electrically isolate the current path from the sensor’s electronics (up to 2.1 kV RMS), which allows the sensor to be inserted anywhere along the current path and to be used in applications that require electrical isolation.
120 kHz bandwith that can optionally be decreased by adding a capacitor across the board pins marked “FILT”.
High accuracy and reliability: typical total output error of 2% at room temperature with factory calibration, an extremely stable quiescent output voltage
Automotive-grade operating temperature range of -40°C to 150°C.
User-settable overcurrent threshold: FAULT pin output latches low when current exceeds the configured threshold for a duration that can be set through the addition of an external capacitor.
The pads are labeled on the bottom silkscreen, as shown in the picture above. The silkscreen also shows the direction that is interpreted as positive current flow via the +i arrow.
The sensor’s extended -75 A to 75 A range should be limited to transient currents. In our tests, we found that the IC could tolerate 50 A for 20 seconds or 37.5 A for 150 seconds before exceeding its maximum temperature rating of 150°C. Therefore, unless you are taking special steps to keep the IC cool, we recommend limiting continuous currents to under 30 A. Even with a low conductive path resistance of 1.1 mΩ, the board can get hot enough to burn you when the current is in the tens of amps, and the IC does not feature any kind of over-temperature protection, so thermal issues should be taken into consideration for high currents.
The only connections required to use this sensor are the input current (IP+ and IP-), logic power (VCC and GND), and the sensor output (VIOUT). All of the other pins are optional, as are the two external capacitors shown in the diagram to the right.
The sensor requires a supply voltage of 3 V to 5.5 V to be connected across the VCC and GND pads, which are labeled on the bottom silkscreen. The sensor outputs an analog voltage that is linearly proportional to the input current. The quiescent output voltage is VCC/2 and changes by 28 mV per amp of input current (when VCC = 5 V), with positive current increasing the output voltage and negative current decreasing the output voltage. For an arbitrary input current i (in amps), the sensor’s output voltage can be more generally represented as:
VIOUT = (0.028 V/A * i + 2.5 V) * VCC / 5 V
The VZCR pin is the voltage reference output pin and can be used as a zero current (0 A) reference. It will be approximately equal to VCC/2 and lets you more accurately compute the current from the VIOUT output voltage.
The FILT pin lets you adjust the board’s bandwidth by adding a capacitor, CF, to ground (a ground pad has been added next to the FILT pin for convenience). Without any external filter capacitor, the bandwidth is 120 kHz. The datasheet provides more information on how the external filter capacitor affects bandwidth.
The FAULT pin is normally high and latches low when the current exceeds the overcurrent fault switchpoint (Ioc). This switchpoint is set by the voltage applied to the VOC pin and is dependent on the voltage divider shown in the schematic diagram below. By default, Ioc is set to 57 A, but it can be altered by adding external resistors to the voltage divider to change the VOC voltage. Once the FAULT pin is latched low, it can be reset by driving the FAULT_EN input low (this input is pulled high on the board). An external capacitor, COC, can be added to increase the overcurrent fault response time. Without this capacitor, the fault response time is typically under 2 us. For detailed information on using the overcurrent fault feature, including some key restrictions on the overcurrent threshold, please refer to the ACS709 datasheet (483k pdf)